How to replace the ignition needle of the old gas range

1. Raise the gas stove. 2. Unscrew the screws. 3. Open the sealing cap. 4. Lift the tempered glass panel. 5. Install a new ignition pin, test the ignition, and the ignition pin is perforated and threaded. 6. Position the fire needle and connect the wire. 7. Test whether the installation is normal. 8. The switch is rusted. Clean it with rust remover and drip some lubricating oil (peanut oil is also OK) for convenience. Extended data: Installation precautions 1. Check whether the type of fuel gas you use is consistent with the type of fuel gas marked on this product. Those that do not conform to the quality can not be installed and used. Check whether each part of the product is installed correctly and whether the screw part is firm to avoid possible wear during transportation, which may affect the use of the product. After checking that there are no problems, we start the installation. 2. Generally, the clear distance between the back of the cooker and the wall is not less than 16cm, and the clear distance between the side and the wall is not less than 20cm; If the wall is made of flammable materials, heat insulation and fire protection layers must be attached. The part of the fire protection layer that is more than both ends of the stove and the part below the stove should not be less than 10cm, and the part that is more than the part above the stove should not be less than 80cm; The minimum distance between the cooker and the cylinder is 1m, and the maximum length of the air inlet hose cannot exceed 2m.

28

2022

/

11

Is it dangerous to loose the ignition needle of the gas stove

Methods for testing the ignition needle of gas cooker: The ignition needle of the gas stove is a metal needle fixed in a ceramic jacket, which has no electronic components. You can judge whether it is damaged by its appearance or use a multimeter to measure its on-off or resistance value; Disassemble the gas cooker, take down the ignition needle and observe whether the metal at the tail and head of the ignition needle is dirty. The resistance from the head to the tail measured by the multimeter should be zero. If the resistance is too large, the surface is too dirty. At this time, polish or replace the ignition needle directly; Observe whether there is crack or high voltage ignition ablation on the ceramic cylinder of the ignition needle jacket. If there is a local yellowing and ignition point, it indicates that the ceramic insulation performance is poor and can not be used any more, and it should be replaced. If there are cracks, replace the ignition pin with a new one in time; Check whether the steel needle and ceramic of the ignition needle are loose or displaced, and if so, replace the ignition needle in time; If the ignition pin and ignition wire are integrated, it is also necessary to measure whether the ignition wire and ignition pin are well connected and whether the resistance is close to zero ohm. If the resistance value is large, it indicates that there is contact resistance. The ignition pin and ignition wire must be reconnected to ensure good continuity.

28

2022

/

11

How to detect whether the ignition needle of gas stove is good or not

Methods for testing the ignition needle of gas cooker: 1. The ignition needle of the gas stove is a metal needle fixed in a ceramic jacket, which has no electronic components. You can judge whether it is damaged by its appearance or use a multimeter to measure its on-off or resistance value. 2. Disassemble the gas cooker, take down the ignition needle and observe whether the metal at the tail and head of the ignition needle is dirty. The resistance from the head to the tail measured by the multimeter should be zero. If the resistance is too large, the surface is too dirty. At this time, polish or replace the ignition needle directly. 3. Observe whether there is crack or high voltage ignition ablation on the ceramic cylinder of the ignition needle jacket. If there is a local yellowing and ignition point, it indicates that the ceramic insulation performance is poor and can not be used any more, and it should be replaced. If there are cracks, replace the ignition pin with a new one in time. 4. Check whether the steel needle and ceramic of the ignition needle are loose or displaced, and if so, replace the ignition needle in time. 5. If the ignition pin and ignition wire are integrated, it is also necessary to measure whether the ignition wire and ignition pin are well connected and whether the resistance is close to zero ohm. If the resistance value is large, it indicates that there is contact resistance. The ignition pin and ignition wire must be reconnected to ensure good continuity.

28

2022

/

11

< 1 >

Baoying Hongbo Electronic Ceramics Co., Ltd.

Sale:+86-18921915900 (Dai Jing)

General Manager:Zheng Renbing

Tel:+86-18994862555

Tel:Ceramic Industrial Park, Liubao Town, Baoying County, Jiangsu Province

这里是标题一h1占位文字


copyright © 2022 Baoying Hongbo Electronic Ceramics Co., Ltd.