Product

Double wire thermocouple (socket A)


The ignition needle of the gas stove is a metal needle fixed in a ceramic jacket, which has no electronic components. You can judge whether it is damaged by its appearance or use a multimeter to measure its on-off or resistance value; 2. Disassemble the gas range, take down the ignition needle and observe whether the metal at the tail and head of the ignition needle is dirty. The resistance value measured from the head to the tail of the multimeter should be zero. If the resistance value is too large, the surface is too dirty. At this time, polish or replace the ignition needle directly; 3. Observe whether the ceramic cylinder of the outer sleeve of the ignition needle has cracks or high voltage ignition ablation. If there are ignition points and local yellowing, it indicates that the ceramic insulation performance becomes poor and can not be used any more, and it should be replaced. If there are cracks, replace the ignition pin with a new one in time; 4. Check whether the steel needle and ceramic of the ignition needle are loose or displaced, and if so, replace the ignition needle in time; 5. If the ignition pin and ignition wire are integrated, check whether the ignition wire and ignition pin are well connected and whether the resistance is close to zero ohm. If the resistance value is large, it indicates that there is contact resistance. The ignition pin and ignition wire must be reconnected to ensure good continuity.

Integrated ignition pin


Pay attention to connect the line at this time. Finally, make an experiment to see if it can ignite. If it can, it means that it can be used normally. Sometimes the ignition needle just shows a little spot. We can remove it with rust remover, and then drop some lubricating oil. It is not necessary to replace it. Precautions for use of gas stove igniter 1. Since the power battery of the igniter is installed inside the shell, install the battery before installing it on the cooker, and open the back cover when replacing the battery. 2. Because the output voltage of the igniter is high, when touching the button, your hands should not touch the discharge pin, so as not to touch the human body with elegant electricity. If you touch it unfortunately, your life will not be endangered. 3. The relative distance between the discharge ignition needle and the burner fire hole shall be appropriate and firm. If it is loose, it shall be adjusted in time to ensure its ignition success rate.

Integrated ignition pin


If it is a liquefied gas stove. First, check whether there is gas in the nocturnal gas cylinder. If there is a small part of gas with low pressure, the fire will be small when cooking. Second, check whether there is a problem with the pressure reducing valve. If it is used at home, generally do not use a high-pressure valve, but use an ordinary pressure reducing valve. Third, check whether the nozzle of the cooker is blocked. Fourth, check whether the place where the fire occurs on the fire cover is blocked. If it is blocked, clear the place where the fire occurs on the fire cover. Generally speaking, these issues are concerned. Generally, there are two reasons for the small fire head of the gas stove. One is that the gas nozzle on the gas stove is blocked. The other is that the pressure limiting valve connecting the gas stove with the LPG cylinder is improperly adjusted, which makes the gas outlet smaller. However, the pipeline gas users have been properly adjusted by the gas company due to the unified gas supply pressure, which generally does not cause low air pressure in a single household. Therefore, if the gas stove has a small fire head, I have the ability to repair the machine, You can close the main gas valve by yourself, find the nozzle of the stove and poke the nozzle hole with a thin steel wire until the gas passes smoothly. If it is not the nozzle of the gas stove, it may be the pressure limiting valve of the liquefied petroleum gas cylinder. Generally, the pressure limiting valve is adjusted clockwise to increase the flame, and counterclockwise to reduce the flame, However, since the LPG pressure limiting valve is composed of rubber diaphragms that are easy to age and expand for a long time, it should not be adjusted as far as possible to avoid leakage and fire. Therefore, in this case, the pressure limiting valve should be sent to the LPG supply station for maintenance. For this problem, don't check anything else. Just take down the rotating fire cover (the round core inside is a straight fire) on the furnace head. There are bamboo toothpicks or small iron wires. The thick needle can remove oxidized iron filings or impurities from the exhaust hole. Because it is iron, it is easy to oxidize impurities and block the air hole. Take out all the iron filings and clean them thoroughly with a cloth.

Ignition wire


If it is a liquefied gas stove. First, check whether there is gas in the nocturnal gas cylinder. If there is a small part of gas with low pressure, the fire will be small when cooking. Second, check whether there is a problem with the pressure reducing valve. If it is used at home, generally do not use a high-pressure valve, but use an ordinary pressure reducing valve. Third, check whether the nozzle of the cooker is blocked. Fourth, check whether the place where the fire occurs on the fire cover is blocked. If it is blocked, clear the place where the fire occurs on the fire cover. Generally speaking, these issues are concerned. Generally, there are two reasons for the small fire head of the gas stove. One is that the gas nozzle on the gas stove is blocked. The other is that the pressure limiting valve connecting the gas stove with the LPG cylinder is improperly adjusted, which makes the gas outlet smaller. However, the pipeline gas users have been properly adjusted by the gas company due to the unified gas supply pressure, which generally does not cause low air pressure in a single household. Therefore, if the gas stove has a small fire head, I have the ability to repair the machine, You can close the main gas valve by yourself, find the nozzle of the stove and poke the nozzle hole with a thin steel wire until the gas passes smoothly. If it is not the nozzle of the gas stove, it may be the pressure limiting valve of the liquefied petroleum gas cylinder. Generally, the pressure limiting valve is adjusted clockwise to increase the flame, and counterclockwise to reduce the flame, However, since the LPG pressure limiting valve is composed of rubber diaphragms that are easy to age and expand for a long time, it should not be adjusted as far as possible to avoid leakage and fire. Therefore, in this case, the pressure limiting valve should be sent to the LPG supply station for maintenance. For this problem, don't check anything else. Just take down the rotating fire cover (the round core inside is a straight fire) on the furnace head. There are bamboo toothpicks or small iron wires. The thick needle can remove oxidized iron filings or impurities from the exhaust hole. Because it is iron, it is most easy to oxidize impurities and block the air hole. Take out all the iron filings and clean them thoroughly with a cloth.

Pyrotechnic ignition needle


Maintenance of flameout protection device of gas cooker: 1. Each furnace head has two needles. One is used for ignition, and the other is the safety device for flameout called thermocouple. When you light a fire, the fire can burn it. At this time, the thermocouple will conduct heat to a solenoid valve under the stove switch. The solenoid valve starts to work, the switch starts to ventilate, and the stove can work normally. If there is no response, the solenoid valve may be broken. Remove the panel, remove a white object connected by two wires at the place where the fire head is adjusted, and replace it with a new one. The problem of automatic flameout is solved. 2. Check whether the connection of the solenoid valve is loose, that is, there is a wire connected to the switch on the furnace head. 3. You can observe whether the furnace fire burns to the thermocouple after ignition. If not, check whether the fire outlet is blocked and pick it with a toothpick. 4. Lift up the gas stove to see if there is a blockage in the air outlet of the ignition place. Poke with a thin wire.

Pyrotechnic ignition needle


This situation may be caused by flame separation due to excessive throttle adjustment. The flame feedback needle cannot sense the flame signal, causing the pulse igniter to still discharge. You can reduce the throttle to reduce the amount of air intake, which can solve the problem of flame separation and flameout. If the throttle is still small, it is recommended to contact the manufacturer's after-sales home inspection office. Introduction: It refers to kitchen appliances heated by direct fire with liquefied petroleum gas, artificial gas, natural gas and other gaseous fuels. Its popularity is unknown, but it is difficult to see a common concept. Like firewood stove, kerosene stove, coal ball stove, etc. According to the gas source, gas stoves are mainly divided into liquefied gas stoves, gas stoves and natural gas stoves. According to the focus, it can be divided into single focus, double focus and multi focus. working principle: When the gas stove is working, the gas enters the stove from the inlet pipe, enters the stove through the adjustment of the gas valve (the user adjusts it through the knob), and mixes some air (this air is called primary air). These mixed gases are sprayed out of the fire hole of the flame divider and ignited by the ignition device to form a flame (the air required for combustion is called secondary air), These flames are used to heat the cooker on the pot stand.

Export type (Sabav ignition needle, with thread)


Methods for testing the ignition needle of gas cooker: The ignition needle of the gas stove is a metal needle fixed in a ceramic jacket, which has no electronic components. You can judge whether it is damaged by its appearance or use a multimeter to measure its on-off or resistance value; Disassemble the gas cooker, take down the ignition needle and observe whether the metal at the tail and head of the ignition needle is dirty. The resistance from the head to the tail measured by the multimeter should be zero. If the resistance is too large, the surface is too dirty. At this time, polish or replace the ignition needle directly; Observe whether there is crack or high voltage ignition ablation on the ceramic cylinder of the ignition needle jacket. If there is a local yellowing and ignition point, it indicates that the ceramic insulation performance is poor and can not be used any more, and it should be replaced. If there are cracks, replace the ignition pin with a new one in time; Check whether the steel needle and ceramic of the ignition needle are loose or displaced, and if so, replace the ignition needle in time; If the ignition pin and ignition wire are integrated, it is also necessary to measure whether the ignition wire and ignition pin are well connected and whether the resistance is close to zero ohm. If the resistance value is large, it indicates that there is contact resistance. The ignition pin and ignition wire must be reconnected to ensure good continuity.

Export type (Sabav ignition needle, with thread)


The famous and hot gas stove tells you that the gas stove is too hot to start. Troubleshooting steps: 1. Observe whether the spark when the gas stove ignites is soft and weak, and the discharge frequency is obviously slower than before. If this is the case, our battery is low, and a new battery will solve the problem. 2. If the spark sound is clear and powerful, but it can't be ignited, then consider whether the gas path is unblocked. It is likely that the nozzle in the furnace head is blocked during use. Take off the distributor cover and use a fine iron wire to pass through the nozzle hole, and then put back the distributor cover to ignite again. 3. Check whether the valve of the valve body of the gas cooker is adjusted too large, which causes too much air flow from the fire hole and shocks the electric spark. The damper can be adjusted from left to right to try to see if the ignition is normal. 4. One furnace head is normal and the other is abnormal. The abnormal side is that there is no spark at all, which means that one of the high-voltage packs in the electronic pulse is burnt out. At this time, the only solution is to replace the pulse. If not, check whether it is the above 2 and 3 cases. 5. It is required to ignite several times continuously, and may not be able to ignite successfully. This situation is mostly caused by thermocouple aging after long-term use. At this time, the only solution is to replace the thermocouple sensor. 6. Ignition is sometimes normal and sometimes abnormal. This is mainly caused by poor contact of the pulse ignition microswitch. Adjust the pulse ignition microswitch to solve the problem.

Infrared medium ignition system


There are three main possibilities for the ignition needle of the gas stove not discharging: 1. The battery is in low power, or simply out of power, and the battery is loose. 2. Switch mechanism failure. The circuit switch of the cooker is usually attached to the edge of the gas knob. The travel of the switch is very small, and the user cannot find it by hand when it cannot be bounced. 3. The pulse igniter of the gas cooker fails, including the short circuit discharge caused by the rupture of the discharge electrode and its insulating magnetic tube. What is the ignition principle of gas stove ignition needle? The ignition mode of gas stove is mainly divided into piezoelectric ceramic ignition and electric pulse ignition. Most modern gas stove igniters are pulse igniters. The pulse igniter is a pulse high-frequency oscillator composed of electronic components. The high-frequency voltage generated by the oscillator is raised to 15KV high voltage through the step-up transformer for tip discharge. The discharged spark ignites the gas on the gas stove. The igniter has high ignition rate and can discharge continuously. Press the knob, and the pulse igniter starts ignition; Release the knob, and the pulse will stop the ignition. How to judge whether the ignition needle is normal? The ignition pin is not easy to break. If the ignition pin does not discharge, it may be that the battery is dead or the pulse igniter is faulty, which is not necessarily the problem of the ignition pin. If the battery is replaced with a new one, it still does not ignite. It is recommended to go to the manufacturer's after-sales service for on-site inspection. How should the gas stove be maintained? The daily maintenance and cleaning of the gas stove is very important. Don't ignore it. If you don't pay attention to the cleaning and maintenance in ordinary days, it will not only affect the beauty of the stove, but also affect the service life of the machine. The cooked food will naturally lose its original taste and nutrition.

Induction needle for atmospheric furnace (with belt thread)


There are three main possibilities for the ignition needle of the gas stove not discharging: 1. The battery is in low power, or simply out of power, and the battery is loose. 2. Switch mechanism failure. The circuit switch of the cooker is usually attached to the edge of the gas knob. The travel of the switch is very small, and the user cannot find it by hand when it cannot be bounced. 3. The pulse igniter of the gas cooker fails, including the short circuit discharge caused by the rupture of the discharge electrode and its insulating magnetic tube. What is the ignition principle of gas stove ignition needle? The ignition mode of gas stove is mainly divided into piezoelectric ceramic ignition and electric pulse ignition. Most modern gas stove igniters are pulse igniters. The pulse igniter is a pulse high-frequency oscillator composed of electronic components. The high-frequency voltage generated by the oscillator is raised to 15KV high voltage through the step-up transformer for tip discharge. The discharged spark ignites the gas on the gas stove. The igniter has high ignition rate and can discharge continuously. Press the knob, and the pulse igniter starts ignition; Release the knob, and the pulse will stop the ignition. How to judge whether the ignition needle is normal? The ignition pin is not easy to break. If the ignition pin does not discharge, it may be that the battery is dead or the pulse igniter is faulty, which is not necessarily the problem of the ignition pin. If the battery is replaced with a new one, it still does not ignite. It is recommended to go to the manufacturer's after-sales service for on-site inspection. How should the gas stove be maintained? The daily maintenance and cleaning of the gas stove is very important. Don't ignore it. If you don't pay attention to the cleaning and maintenance in ordinary days, it will not only affect the beauty of the stove, but also affect the service life of the machine. The cooked food will naturally lose its original taste and nutrition.
< 1 >

Baoying Hongbo Electronic Ceramics Co., Ltd.

Sale:+86-18921915900 (Dai Jing)

General Manager:Zheng Renbing

Tel:+86-18994862555

Tel:Ceramic Industrial Park, Liubao Town, Baoying County, Jiangsu Province

这里是标题一h1占位文字


copyright © 2022 Baoying Hongbo Electronic Ceramics Co., Ltd.