Export type

Product

Integrated ignition pin

Pay attention to connect the line at this time. Finally, make an experiment to see if it can ignite. If it can, it means that it can be used normally. Sometimes the ignition needle just shows a little spot. We can remove it with rust remover, and then drop some lubricating oil. It is not necessary to replace it. Precautions for use of gas stove igniter 1. Since the power battery of the igniter is installed inside the shell, install the battery before installing it on the cooker, and open the back cover when replacing the battery. 2. Because the output voltage of the igniter is high, when touching the button, your hands should not touch the discharge pin, so as not to touch the human body with elegant electricity. If you touch it unfortunately, your life will not be endangered. 3. The relative distance between the discharge ignition needle and the burner fire hole shall be appropriate and firm. If it is loose, it shall be adjusted in time to ensure its ignition success rate.

隐藏域元素占位

Integrated ignition pin

If it is a liquefied gas stove. First, check whether there is gas in the nocturnal gas cylinder. If there is a small part of gas with low pressure, the fire will be small when cooking. Second, check whether there is a problem with the pressure reducing valve. If it is used at home, generally do not use a high-pressure valve, but use an ordinary pressure reducing valve. Third, check whether the nozzle of the cooker is blocked. Fourth, check whether the place where the fire occurs on the fire cover is blocked. If it is blocked, clear the place where the fire occurs on the fire cover. Generally speaking, these issues are concerned. Generally, there are two reasons for the small fire head of the gas stove. One is that the gas nozzle on the gas stove is blocked. The other is that the pressure limiting valve connecting the gas stove with the LPG cylinder is improperly adjusted, which makes the gas outlet smaller. However, the pipeline gas users have been properly adjusted by the gas company due to the unified gas supply pressure, which generally does not cause low air pressure in a single household. Therefore, if the gas stove has a small fire head, I have the ability to repair the machine, You can close the main gas valve by yourself, find the nozzle of the stove and poke the nozzle hole with a thin steel wire until the gas passes smoothly. If it is not the nozzle of the gas stove, it may be the pressure limiting valve of the liquefied petroleum gas cylinder. Generally, the pressure limiting valve is adjusted clockwise to increase the flame, and counterclockwise to reduce the flame, However, since the LPG pressure limiting valve is composed of rubber diaphragms that are easy to age and expand for a long time, it should not be adjusted as far as possible to avoid leakage and fire. Therefore, in this case, the pressure limiting valve should be sent to the LPG supply station for maintenance. For this problem, don't check anything else. Just take down the rotating fire cover (the round core inside is a straight fire) on the furnace head. There are bamboo toothpicks or small iron wires. The thick needle can remove oxidized iron filings or impurities from the exhaust hole. Because it is iron, it is easy to oxidize impurities and block the air hole. Take out all the iron filings and clean them thoroughly with a cloth.

隐藏域元素占位

News

undefined

undefined

Is it dangerous to loose the ignition needle of the gas stove

Methods for testing the ignition needle of gas cooker: The ignition needle of the gas stove is a metal needle fixed in a ceramic jacket, which has no electronic components. You can judge whether it is damaged by its appearance or use a multimeter to measure its on-off or resistance value; Disassemble the gas cooker, take down the ignition needle and observe whether the metal at the tail and head of the ignition needle is dirty. The resistance from the head to the tail measured by the multimeter should be zero. If the resistance is too large, the surface is too dirty. At this time, polish or replace the ignition needle directly; Observe whether there is crack or high voltage ignition ablation on the ceramic cylinder of the ignition needle jacket. If there is a local yellowing and ignition point, it indicates that the ceramic insulation performance is poor and can not be used any more, and it should be replaced. If there are cracks, replace the ignition pin with a new one in time; Check whether the steel needle and ceramic of the ignition needle are loose or displaced, and if so, replace the ignition needle in time; If the ignition pin and ignition wire are integrated, it is also necessary to measure whether the ignition wire and ignition pin are well connected and whether the resistance is close to zero ohm. If the resistance value is large, it indicates that there is contact resistance. The ignition pin and ignition wire must be reconnected to ensure good continuity.

隐藏域元素占位

undefined

undefined

How to replace the ignition needle of gas cooker

Pay attention to connect the line at this time. Finally, make an experiment to see if it can ignite. If it can, it means that it can be used normally. Sometimes the ignition needle just shows a little spot. We can remove it with rust remover, and then drop some lubricating oil. It is not necessary to replace it. Precautions for use of gas stove igniter 1. Since the power battery of the igniter is installed inside the shell, install the battery before installing it on the cooker, and open the back cover when replacing the battery. 2. Because the output voltage of the igniter is high, when touching the button, your hands should not touch the discharge pin, so as not to touch the human body with elegant electricity. If you touch it unfortunately, your life will not be endangered. 3. The relative distance between the discharge ignition needle and the burner fire hole shall be appropriate and firm. If it is loose, it shall be adjusted in time to ensure its ignition success rate.

隐藏域元素占位

Baoying Hongbo Electronic Ceramics Co., Ltd.

Sale:+86-18921915900 (Dai Jing)

General Manager:Zheng Renbing

Tel:+86-18994862555

Tel:Ceramic Industrial Park, Liubao Town, Baoying County, Jiangsu Province

这里是标题一h1占位文字


copyright © 2022 Baoying Hongbo Electronic Ceramics Co., Ltd.